TUTORIAL: How to replace the grilles on your BMW?

OUR TUTORIAL FOR CHANGING YOUR BMW OEM GRILLES

One of the most frequently damaged parts on the road, your grille is often the first accessory to replace when you want to change the look of your BMW.

However, it can be intimidating at first to have to remove these spare parts on your vehicle, which is why we offer a tutorial to help you with the removal and reinstallation of your BMW grilles.

BMW Black Grilles

Give your BMW a more aggressive and modern look. Simple installation, premium quality, free shipping — 1-year warranty.

View the selection

Our assembly tutorial applies to the following models:

BMW 1 Series E87 (2004-2011)

BMW 1 Series F20 (2011-2019)

BMW 2 Series F22 (2014-2021)

BMW 3 Series E90/E92 (2005-2013)

BMW 3 Series F30 (2011-2019)

BMW 3 Series G20 (2019-2025)

BMW 4 Series F32 (2012-2020)

BMW 4 Series G22 (2020-2025)

BMW 5 Series E60 (2003-2010)

BMW 5 Series F10 (2010-2017)

BMW 5 Series G30 (2018-2024)

BMW 6 Series F12 (2011-2017)

BMW 7 Series F01 (2008-2015)

BMW 7 Series G11 (2016-2022)

BMW X1 E84 (2009-2015)

BMW X1 F48 (2015-2022)

BMW X3 F25 (2010-2017)

BMW X3 G01 (2017-2025)

BMW X4 F26 (2014-2018)

BMW X4 G02 (2018-2025)

BMW X5 F15 (2013-2018)

BMW X5 G05 (2018-2025)

BMW X6 F16 (2014-2019)

BMW X6 G06 (2019-2025)

Estimated duration: 15 to 20 minutes

Tools needed:

T20 Torx
T30 Torx
A small flathead screwdriver or a lever (you can find these tools at Facom, KS Tools, Stanley stores…)

📋 Detailed steps:

1. Open the hood and remove the rubber seal

Locate the hood seal , situated at the front of the engine compartment. Carefully remove it by pulling from one side to the other to access the screws at the top of the bumper.

2. Unscrew the top screws

There are 8 Torx screws in total to remove (the total number varies depending on your model):

- 6 T30 screws (3 on each side)

- 2 T20 screws , located above each headlight

Put them aside in a small container to avoid losing them.

3. Loosen the top of the bumper

Once the screws are removed, gently pull the top of the bumper forwards , without lifting it upwards. This prevents breaking the metal clips located behind it.

The bumper is flexible enough to allow your hand or a tool to pass between it and the grilles.

4. Access the grilles

Gently pull on the outer corners of the bumper to gain some flexibility. It's often easier to start with the outermost grille (especially if you have large hands).

5. Unclip the old grilles

Using your flathead screwdriver or lever , push on the locking tabs located behind the grille:

- 3 clips at the top

- 3 clips at the bottom

- 1 clip on each side

💡 For the lower clips (facing the ground), use your fingers if the space is too narrow for a tool.

6. Remove the first grid

Once unclipped, gently pull the grille outwards. The clear opening will make it easier to access the second one.

7. Install your new grilles

Position the new grille opposite the slots, then gently push until you hear a click . Run your hand all around the frame to check that all the clips are properly engaged .

🧼 Tip: Wipe with a microfiber cloth to remove fingerprints.

8. Reposition the bumper and screw it back on.

Slide the top of the bumper back into place, properly aligning the metal clips .

Screw the 8 Torx screws back in, but before tightening, check that the gap between the bumper and the bodywork is symmetrical on both sides. Adjust if necessary.